Compressed Air Leaks: What They Cost and How to Find Them

Published on

Compressed air leaks: what they cost and how to find them

The short answer: a leak costs you the electricity needed to make the air that escapes. A hole of 3 mm, about the size of a worn quick coupling, lets out roughly 20 CFM at normal plant pressure. At ₹22 per 1,000 cubic feet of air, that is about ₹1.3 lakh a year on a two-shift plant, and about ₹2.2 lakh if you run round the clock. Most plants have dozens of leaks, so the total is often 10–20% of everything the compressor makes.

Leaks are easy to ignore. You can't see them, the noise disappears under the sound of production, and the compressor simply runs harder to cover them. Below is how to put a number on yours, where to look, and how to keep them down.

Why a leak costs so much

A compressor turns electricity into air. Every cubic foot that escapes through a leak had to be made first, with the same power as the air that reaches your machines. And a leak doesn't stop at tea break or between batches. It runs every hour the system is under pressure.

In our screw compressor running cost guide, a Colt CS 50 (37 kW, 242 CFM at 8 bar) on a two-shift plant makes air at about ₹22 per 1,000 cubic feet at ₹8 per kWh. We use that figure for the costs below.

What a leak costs a year

Leak sizeAir lost (about, at 6–7 bar)Cost a year, 2 shifts (4,800 h)Cost a year, round the clock (8,400 h)
1 mm hole (a loose fitting)2 CFM₹12,700₹22,000
3 mm hole (a worn coupling or split hose)20 CFM₹1.3 lakh₹2.2 lakh
5 mm hole (a drain left open, a cut hose)55 CFM₹3.5 lakh₹6.1 lakh

Costs are at ₹22 per 1,000 cubic feet. The air lost through a hole of a given size is a general engineering figure, and it rises with pressure.

Look at the 5 mm line. A single drain valve left cracked open can waste about a quarter of what a 50 HP compressor makes.

Put it together for a plant: if a CS 50 is losing 30 CFM to leaks, that is about one-eighth of its output, and about one-eighth of the power bill goes with it.

Test 1: the load/unload test (no tools needed)

This works on any screw compressor with a load/unload controller.

  1. Pick a time when production is stopped: a Sunday, or the gap between shifts.
  2. Close every outlet and switch off every machine that uses air. Leave the compressor running.
  3. With nothing using air, the compressor should stay unloaded. Any time it spends loaded is going into leaks.
  4. Time several load and unload cycles with a stopwatch.

Leak % = loaded time ÷ (loaded time + unloaded time) × 100

For example, if the compressor loads for 30 seconds and unloads for 2 minutes 30 seconds, your leaks are 30 ÷ 180 = about 17% of its output.

How to read the result:

  • Up to 10%: a well-kept system.
  • 10–20%: typical for a plant that has never been checked for leaks.
  • Above 20%: significant. Worth acting on now.
  • Above 50%: unusually high. Check that every outlet really was closed, and test again.

Our free compressed air leak calculator does this sum for you. Enter your compressor kW, running hours, tariff and the test timings, and it shows what your leaks and any extra pressure cost you each year. It works on any make of compressor.

Test 2: the receiver pressure-drop test

If your compressor is a VFD machine, or you want a figure in CFM, use the air receiver instead.

  1. With production stopped, run the compressor up to full pressure, then switch it off. Keep the receiver connected to the plant pipework.
  2. Note how long the pressure takes to fall by a set amount, say from 8 bar to 6 bar.
  3. Work out the leak:

Leak (m³/min of free air) = volume (m³) × pressure drop (bar) ÷ (time in minutes × 1.013)

Use the volume of the receiver plus the pipework, if you know it. Using the receiver alone gives a figure on the low side.

Example: a 1,000 litre receiver (1 m³) falls from 8 to 6 bar in 2 minutes. Leak = 1 × 2 ÷ (2 × 1.013) = about 1 m³/min, or 35 CFM. On the two-shift basis in the table, that is about ₹2.2 lakh a year.

Run either test every month and write the result down. It's the simplest way to see whether leaks are creeping back.

Where leaks usually are

In the plants we visit, most leaks are in the same few places:

  • Quick couplings and hoses at the machines, especially on hoses that get dragged around the floor.
  • Filter-regulator-lubricator (FRL) units and pressure regulators at the machine.
  • Condensate drains. Manual drains left cracked open "to be safe", and timer drains that stick open. One open drain can be the biggest leak in the plant.
  • Threaded joints and flanges, especially on old galvanised pipework.
  • Cylinders and valves with worn seals, which leak even when the machine is idle.
  • Air guns and blowing points left open, or used for cleaning instead of a brush.
  • Old branch lines to machines that were moved or scrapped but never isolated.

How to find and fix them

  1. Listen. On a quiet day with the plant pressurised, walk the whole line. Most large leaks can be heard.
  2. Soap test the rest. Brush soapy water on joints and fittings; a leak shows as bubbles. An ultrasonic leak detector finds small leaks in a running plant, when the noise hides them.
  3. Tag each leak with a label and list it. Fixing them in one go during a shutdown is quicker than chasing them one at a time.
  4. Replace, don't patch. Worn couplings, hoses and seals are cheap compared with a year of lost air.
  5. Fit automatic drains. An electric timed drain valve opens only for a few seconds at a time, so nobody has to leave a manual drain open. See our air accessories page.
  6. Isolate what isn't used. Put a valve on each branch and close it when that section is not working.
  7. Test again with Test 1 or Test 2 to see what you saved.

Two things that make leaks cost even more

Pressure set too high. A leak lets out more air at higher pressure. And every 1 bar of extra pressure costs roughly 6–7% more power across the whole plant. If your machines work at 7 bar, don't run the compressor at 9 bar to make up for losses. Find the pressure drop in the piping, dryer or filters and fix that instead.

A compressor that unloads a lot. Once the leaks are fixed, demand falls. A fixed-speed compressor then spends more time unloaded, still drawing 20–30% of its full power while making no air. A VFD screw compressor slows down instead, so the saving from fixing leaks reaches the electricity bill. On plants where demand swings, a VFD saves up to 35% of the energy.

Fix leaks before buying a bigger compressor

When the pressure at the far end of a plant starts dropping, the first thought is often to buy a bigger compressor. Check the leaks first. A plant losing 20% of its air through leaks can often get by with the compressor it already has, once the leaks are fixed. If you do need more air after that, size the new machine on the real demand: add up what runs at the same time and add about 20%. Our screw air compressor page has the full model table, from 10 to 350 HP, and a quick sizing guide.

Frequently Asked Questions

A plant that has never been checked typically loses 10–20% of the compressor's output. A well-kept system stays under 10%. Above 20% is worth fixing straight away.

Large ones, sometimes, by listening during a quiet moment. Small leaks are hidden by production noise; an ultrasonic leak detector finds them in a running plant. The load/unload test and the receiver test have to be done with production stopped.

No. A VFD doesn't fix a leak, and leaks still cost money with any compressor. But once you fix them, a VFD machine turns the lower demand into a lower power bill by slowing down, instead of running unloaded.

Yes. A leak lets out less air at lower pressure, and the compressor uses less power for every cubic foot it makes. Set the pressure to what your machines actually need, plus the drop across the dryer, filters and piping.

Yes. Our annual maintenance contracts include leak and safety checks on the piping, valves and controls along with the compressor service.

Find out what your leaks cost

Run the load/unload test, then put the timings into our leak calculator. If you'd like help, send us your compressor's kW, running hours, working pressure and the test results through our contact page. Our engineers will work out what the leaks are costing you and whether your compressor is the right size once they're fixed.